Water Heater Repair Moreno Valley's Blog

Moreno Valley CA Homeowner advice and maintenance tips for water heaters.

Water Heater Repair Moreno Valley Infographic

We have designed an infographic displaying the different water heater repair services we offer, and wanted to show it to our customers and followers today.  We are available 24 hours a day for any emergency water heater or plumbing repairs you might need!  Don’t be reluctant to contact Water Heater Repair Moreno Valley any time.

Water Heater Repair Moreno Valley Infographic

Water Heater T&P Valve Test

The Causes of a Water Heater Tank Explosion

In terms of needing to undertake servicing on ones water heater, it is a pretty low maintenance device. However, one necessary element of it should be checked out regularly. Hot Water Heater Repair Moreno Valley would like to pass along this safety information regarding ones water heater today.

Too much temperature when put together with tank deterioration within the storage tank could potentially cause an explosion. If the water temperature is below 212 degrees Fahrenheit, one will be safe from an explosion, though there is a associated risk of scalding at that temperature. But, if the water temperature is over 212 degrees, water turns into steam, which will then enlarge to 1,700 times the space it occupies as water. This is when an explosion can happen.

Cautionary Signals of a Water Heater Explosion
The leading sign is if one goes to get hot water from a faucet and only steam comes out. Without delay turn off power if one possesses an electric water heater. If one owns a gas hot water heater, shut off the gas valve going to the water heater. After that, give us a call to come examine the predicament.

Minimizing Potential Water Heater Dangers
The most important upkeep activity having a water heater is to examine the pressure relief valve, referred to as the T&P valve, on a standard schedule. This valve helps control the pressure buildup on the interior of the water storage tank to avert a dangerous increase in temperature and overpressure.

Caution!
Be careful, the water discharge out of a T&P valve might be quite hot. If you do not feel comfortable evaluating the valve contact us. Additionally, undertaking any sort of repairs to the valve should really be executed by a experienced plumbing repair business.

How to Test the T&P Valve

Clear the space around the overflow pipe and floor drain.
Lift up the test handle for around 5 seconds or until the water runs clean.
Let go of the handle.
If the T&P valve keeps on running with water, raise the handle up and down rapidly to get it to reseat itself. One may need to do this a few times. IF it has not been tested for a while, it might be difficult to raise it at first. Don’t use a lot of force, but might need to make use of a little.
If the T&P valve remains leaking, it should be changed.
Additional points to watch out for are corrosion on the stem of the valve. If there is any water leaking out of the valve stem or out of the drain valve.

Interested in more suggestions? Take a look at our additional articles here:

Water Heater Maintenance Infographic

Moreno Valley Water Heater Maintenance

Related T&P Valve Testing Videos

Mythbusters did a test of the potential dangers of hot water heater explosions here:

Water Heater T&P Valve Repair Moreno Valley

What the Experts Say

  • The discharge from a T&P valve can be very hot. It is very important that all T&P valves be installed properly with a discharge line piped downward to an adequate drain to avoid property damage and to minimize possible human contact.
    Read more…

Watts Water Technologies

If the temperature in your heater remains high after you turn down the thermostat, the thermostat may be faulty. Consult a professional for repair. Read more…

Home Guides

Pressure relief valves sometime develop a drip when opened for the first time in years. Try opening and closing it a few times to see if it will seat itself. If you have a large leak or the drip doesn’t stop on its own in a day or two, the valve will need to be replaced.  Read more…

Today's Homeowner

Check out some of our other water heater tips in our blog

Eliminating Water Heater Odors in Your Moreno Valley Home

Moreno Valley Water Heater Odor Repair

Are you having an issue with smelly odors coming from the water originating from your water heater? It occurs at times for a couple different reasons. Here is what Water Heater Repair Moreno Valley suggests to do to make sure your water smells far better and to eliminate any undesirable taste soon.

Causes for Moreno Valley Water Heater Smells?

Bacteria getting into the water system is the most typical explanation ones water at home could have smells. If you home utilizes well water or cities that use wells for the water supply, will increase the likelihood of this developing.

With a water heater temperature setting of 140 degrees or more will help in cutting down on the development of bacteria inside the water storage tank.

The Best Ways to Eliminate Stinky Water Smells

The following directions describe how you can use chlorine bleach to wash a water heater.

The electric or gas leading to the water heater tank needs to first be turned off.

Next, the cold water supply off that goes to the tank needs to be shut off.

Open the hot water faucet of the kitchen area sink to enable air to enter the tank.

With a a garden hose attached to the storage tank drain valve, drain the water inside the water heater.

Then shut the drain valve once it is drained.

The next step is putting in the bleach.
If the pipe for the cold water travelling inside the storage tank is a flexible hose, unscrew it from the tank. Otherwise, one will probably need to take off the pressure relief valve, which is more involved. For electric water heaters, one of the elements can be removed.

Make use of a funnel to put bleach into the tank.
Add 5 ounces of bleach for every gallon of the tank ability.
So if you have a 50 gallon water heater, you will require 250 ounces of bleach, or close to 2 gallons.

Hook the water line or pressure relief valve back up again

Fill the tank back up with water again.

Close up the hot water faucet of the kitchen faucet as quickly as all the air is out of the line.

Operate all the hot water appliances up until the odor of bleach is apparent. We want to kill the microorganisms that can be found in the water lines also, not just within the water heater.

Allow the water to stay in the tank and water lines undisturbed for 2 to three hours.

Drain the storage tank again and refill it. This time allow it to remain for at least 30 minutes and once again drain it.

Fill the tank back up. Turn on all of the hot water fixtures and let them run till the odor of bleach is gone.

For gas water heaters, relight the water heater pilot burner. For electric water heaters, turn the power on once more.

In addition, by replacing the anode rods, or simply the type used can accomplish the same goal as the following video illustrates:

Additionally, by replacing the anode rods, or perhaps the type employed can work as the next video shows:

Odors from Moreno Valley Water Heater

What the Experts Say

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more here…

Soquel Creek Water District

How is hydrogen sulfide gas produced in a water heater?

A water heater can provide an ideal environment for the conversion of sulfate to hydrogen sulfide gas. The water heater can produce hydrogen sulfide gas in two ways – creating a warm environment where sulfur bacteria can live, and sustaining a reaction between sulfate in the water and the water heater anode.  Read more…

Minnesota Department of Health

Check out some of our other water heater tips in our blog

Best Water Heater Temperature Level

An element regarding ones water heater of which a good number of Moreno Valley homeowners has likely definitely not considered a lot concerning is the temperature setting. What exactly is the ideal temperature level for the hot water in ones house? In this post Water Heater Repair Moreno Valley CA will focus on the benefits and drawbacks of various levels for house owners to decide on what is going to work most effectively for them and their family, for there are a few health dangers that ought to be taken into consideration.

Many water heater suppliers preset the temperature of their hot water heaters to 140 degrees. If you have gotten the heater in your property installed or changed while being there, this might be exactly what it is already set at if you never have adjusted it. It may be tough to find out precisely what the true temperature is on quite a few water heater units for the dial is referred to as as warm, hot, really hot. We are convinced it appears like a very good promoting option to market water heaters that have the ability to heat water to 1000 degrees, nonetheless we will find that it is quite unneeded.

In the event the temperature dial has no degrees written upon it, fill up a glass of hot water from a faucet and put a cooking thermometer inside it to see the temperature level.

Energy Saving Costs With Moreno Valley Water Heater Temperature Settings

It happens to be presumed that through shifting the setting from 140 to 120 degrees can save between six to ten % of the energy made use of from the water heater. In money, this would allow $6 to $20 annually in cost savings. The U.S. Department of Energy expresses a temperature setting of 120 is a great strategy to lower home energy costs.

If in conclusion of the article one thinks an even lower temperature setting is secure for ones house, subsequently the financial savings may well be more than suggested earlier.

Potential Health Risks With Water Heater Temperature Settings

As the infographic beneath displays, there may be health dangers if the hot water temperature is too cool. Legionella bacteria is the possible dangerous variable to consider. It could possibly grow in the temperature spectrum of 68 to 122 degrees. Therefore, if ones water heater is placed beneath 122 degrees, there exists the likelihood it could grow on the inside of ones hot water heater storage tank.

How is Legionella bacteria harmful? A type of pneumonia could be transferred if an individual breathes water that Legionella bacteria has contaminated. This would most often take place when inhaling water moisture by a shower. Consuming the water is normally alright.

Approximately 8,000 to 18,000 Americans catch this annually states the Centers for Disease Control and Prevention, and 5 to 30 % of such instances result in death. This is not stated to distress anyone, but just as a useful idea for all those that may be much more susceptible to acquiring Legionella Disease.

According to OSHA, “At low levels of contamination, the chance of getting Legionnaires’ disease from a water source is very slight. The problem arises when high concentrations of the organism grow in water systems. Water heaters, cooling towers, and warm, stagnant water can provide ideal conditions for the growth of the organism.”  (read more)Moreno Valley Water Heater Repair

Arguments to Decrease Water Heater Temperatures

Among the arguments to never have ones water heater established at approximately 140 degrees is the risk of getting scalded or burned by the water. For Moreno Valley property owners that have youngsters or older adults, this ought to be taken into account. The Consumer Product Safety Commission (CPSC) proposes a setting of 120 because of motives. One can find currently bath faucet slip covers that have a LED temperature reading that are useful also!

When reducing the temperature setting, examine the dishwasher manual to find out what the the bare minimum water temperature level is for it. Several brands require it to be fairly high.

This is often a challenging subject to make a decision on Hot Water Heater Repair Moreno Valley understands. We trust the material in this article and the infographic underneath will help inform our Moreno Valley neighbors and clients on the preferred water heater temperature issue.

Hot Water Heater Repair Moreno Valley

Total Water Heater Maintenance Tips

Water Heater Repair Moreno Valley is not about to pass on the regrettable testimonies pertaining to water heater maintenance of “stumbling out of bed to the chilly bath,” here. Additionally, we are going to presume that one is aware of the basic concept of making certain ones water heater is maintained systematically to receive the most from its life. This may help one spend less on energy costs as well. All of that is sensible we realize. While hot water heaters don’t require a lot when it comes to maintenance (and we are amazed, even though not shocked, by the quantity of customers we come across who have not carried out anything to their water heater), listed below are the duties people must know with regards to routine maintenance.

How Long Should My Moreno Valley Water Heater Last?

The standard gas water heater can last 8 to 10 years. There are numerous elements which will impact the general lifetime naturally, however this is a very good standard. Most likely the largest variable which will impact the long life of it is actually mineral deposits. A number of the tips following should go a long way in assisting to minimize the accumulation of mineral deposits inside of the storage tank of the water heater.

Moreno Valley Water Heater Repair PreventionHot Water Heater Repair Moreno Valley

Property owners, even the ones which never feel excessively handy, are able to do plenty of water heater servicing independently. However more often than not, water heaters are harmless, it is essential to be aware of that they actually operate from an electrical source and/or gas, therefore appropriate safety actions must be implemented. Make sure to utilize these methods as an informative tutorial, for we’d much rather demonstrate all these together with you directly. The electric power to the water heater requires to be switched off previous to carrying out any servicing. Ones breaker box ought to have a with any luck labeled switch to specify which breaker is the heater’s. With a gas heater, turn the gas cutoff counterclockwise to switch off the gas to the device.

The section of the heater that facilitates with protecting against rusting on the inside the water storage tank are the anode rods, or additionally known as sacrificial anode rods. Almost all are composed of aluminum or magnesium around a steel wire. Eventually the external covering of the rods will erode and they need to be replaced at the time the steel wire is obvious. They generally last around 5 years, though that could be reduced if ones water is soft. Over time, it is much easier and cost effective to have the anode rods changed, in an effort to have an extended life from the water heater storage tank. The rods ought to be reviewed each year basis.

The follow video does a terrific job of showing the technique needed with replacing the anode rods:

Not every water heater has dip tubes. They must be inspected for deterioration every 6 months. To test it, take it out and check its length to the height of the water heater. It ought to be roughly 6″ to 8″ shorter as compared to the tank. In cases where it’s smaller than that, as well as exhibits symptoms of breakage or falling apart, it’ll need to get changed.

The big and small flush. Once again, mineral deposits are the primary reason of water heater malfunctions. Based on the level of quality of water in ones house will establish just how quick sediment will build up within the storage tank. This sediment can solidify with time, creating peculiar popping sounds from the storage tank, lessen the effectiveness of the device, and sometimes block up the drain valve. Ideally, every 6 months, but at a minimum annually, empty 1 or 2 gallons of water from the drain valve in the bottom of the hot water heater in a pail or by a hose in a container outdoors. Look to find out what amount of sediment is within the pail when the water settles. If it appears to be reasonably clear, that great! When these types of small flushes are performed two times per year, one will possibly not need to carry out a big flush as frequently. If the water appears very dirty, a full flush needs to be carried out. This can be likewise a very good occasion to ensure the bottom drain valve of the storage tank is operating good and not leaking. They are generally constructed from plastic and after a while when they aren’t opened up, they might get stuck or not close up properly, so opening and closing them at the time of the small flush test is very good.

There can be distinctive actions one may take through flushing to manage any sort of water smells which may arise when hot water comes from faucets within the house also.

This video displays exactly how and reasons behind a water heater flush:

With regard to holiday or temporary households, one ought to empty the storage tank of all its water to stop any kind of flooding when the house is not being occupied. Of course, ensure to fill it up whenever the property is to be resided in once again.

Water pipe inspection. Analyze to ensure all water piping don’t have leaks or are defective at all. It ought to be simple and easy to see when there are any leaks coming from any component of the water plumbing or storage tank for there’ll be water underneath it and/or close to the device. Leaking water could potentially cause water damage to elements of ones dwelling, so ensure all appears to be dry, specifically if the heater is situated on the inside of the household and not in a garage.Moreno Valley Water Heater Repair

T&P valve examination. The T&P valve, also referred to as the temperature and pressure relief valve, ought to be tested yearly. The function of the T&P valve would be to safeguard the water heater storage tank from surplus pressure, and exploding, not to frighten anybody. The owners guide needs to be looked over to be sure the appropriate actions are taken but listed below are the standard techniques. A little water can come out of the valve and it will likely be really hot so be cautious. Lift up the handle and let go of it. Have a container prepared to catch any unwanted water that could come out. Additionally, the noise of pressure getting discharged will be observed. The handle needs to snap back in position. If perhaps it fails to give it a try once more. When it will not go back again into position following several attempts, it is going to have to be changed. The valve might drip a little water after doing that for a little while. If it doesn’t quit dripping after a number of hours inform us.

There is certainly a great deal of discussion around what the finest temperature setting should really be. The manufacturer pre-programmed setting is typically 140 degrees, which is actually warmer than the majority of people may ever need to have. 120 degrees is the standard temperature and some actually go as far as 100 degrees. We are publishing much more on this issue shortly, but we recommend not going over 120 degrees.

Just For Gas Water HeatersWater Heater Repair Moreno Valley

The gas venting system requires being examined each 3 months. Take a look at to guarantee all fittings are tight and for obstructions and deterioration to the vent pipes in addition to ensuring these are totally free of rust and deterioration .. Gas fired hot water heaters vent fumes to the outdoors of the residence. If these fumes flow inside of the residence it really is fatal and a fire danger. Ensure everything combustible or corrosive is clear of the exhaust ventilation to assist in preventing fires. Change all loose, broken or corroded segments of vent pipes.

Look at the pilot light to carry out a visual evaluation of just how it is working. The pilot light is the piece that ignites the gas burner which will heat the water. A clean burning and correctly adjusted pilot light is necessary for your water heater to function at peak efficiency. The color of the flame of the pilot light really should be blue with natural gas heaters or blue/green with just a bit of yellow at the tip with propane heaters. A weakened flame, a yellow flame, or a flame which has a divided flame on the top signifies that a resetting is required.

Just For Electric Water Heaters

Making use of insulation wraps or covers around the storage tank should help preserve a consistent temperature inside of the storage tank without making use of as much electric power. In addition, with the heater not needing to operate as much will stretch the life span of the heating element because it will not be utilised as much. Every 3 months perhaps, examine to verify the insulation cover continues to be attached properly and hasn’t fallen or shifted on the water storage tank.

Occasional assessment of the heating element is very important and may help minimize the need for an unexpected emergency repair. We aren’t going to get into the aspects for a complete test at this point, however one will require a voltage/OHM meter to assure there exists a closed electrical circuit. Heating elements will need changing at times.

Continue to keep the vicinity near ones water heater thoroughly clean of dirt. Particularly if the water heater is situated in the garage area, make certain to keep the place swept. The cleaner the heater is, the significantly better it is going to run without having the requirement of a water heater repair.

Replace Old Water Heaters With Energy Efficient Ones

Today, virtually all water heaters designed have got a good quantity of energy efficiency. In April of 2015, new rules were set up in the United States on water heaters. Clearly, the better the heater, the longer the life one is certain to get from the device using the proper upkeep through the years. Don’t be reluctant to get in touch with Hot Water Heater Repair Moreno Valley to talk about water heater maintenance or maybe to help answer any problems on choosing the most suitable replacement water heater for ones household or workplace. Brand, model, and size have to all be considered in the course of the selection process and not merely utilize the “bigger the better” slogan. Pertaining to storage tank water heaters, one won’t desire to be continuously preserving a surplus quantity of hot water that won’t be used.

Water Heater Troubleshooting Strategies

Hot water heaters are one of a house’s most diligently operating devices. Day or evening, it’s producing completely heated water at any time when you would like it. When it unexpectedly is no longer working effectively, many of us have a tendency to worry.

Thankfully a nonfunctioning water heater does not constantly imply a pricey repair work. Prior to making an emergency call to Water Heater Repair Moreno Valley CA, we recommend examining the trouble yourself first.

Moreno Valley Water Heater Repair Troubleshooting

Check the Pilot Light

For a gas water heater, eliminate the small panel on the bottom of the appliance and look to notice if the pilot light is ignited.
Spark it with a match or lighter to re-ignite it. If it remains lit, the water heater ought to kick-in and begin performing correctly.
If the pilot burner on the water heater does not remain ignited, you might require to change the thermocouple or have the burner cleaned.

Replace the ThermocoupleHot Water Heater Repair Moreno Valley CA

It seems like a extremely technological title, however it’s in fact a basic gadget that you can change on your water heater.

Check the owner’s guide. It ought to have directions for ways to get rid of and change the thermocouple.
Switch off the gas prior to taking out anything at all from the water heater.
Using the guidelines in your individual’s handbook, eliminate the thermocouple by separating it from both sides of the aviator line.
Change the thermocouple on the water heater with a brand-new one that is cut to length.
Turn on the gas and check for leakages, then re-light the pilot light.

Hit the Reset Button

If you have an electric water heater, find the reset button and push it till you notice a click.
If you do not notice a click, or it falls short to reboot the water heater, reset the breaker.
If a breaker reset does not suffice, you could have to change the thermostat.

Change the Thermostat

Shut down the power to the water heater, and turn off the breaker it is linked to. You do not wish to electrocute yourself!
Use the owner’s guide to find the thermostat wires, then separate them.
Eliminate the thermostat and have it checked by a home appliance dealership. If it is defective, change it.

Change the Heating Element

With the power still turned off, get rid of the gain access to panel on the water heater.
Loosen the terminal screws and pull the wires far from the heating element.
Get rid of each part of the element and have them checked by a device repair shop. If they are malfunctioning, change them.

Your water heater must be working in no time. If these actions fall short to repair your hot water heater, or if you do not feel relaxed doing them by yourself, call Hot Water Heater Repair Moreno Valley.

Repairing a Noisy Moreno Valley Water Heater

Water Heater Repair Moreno Valley CA is frequently being contacted to have a look at a loud water heater. Popping and knocking noises might be resulting from a problem with the water heater, but it’s additionally an inconvenience. We are going to explore the most probable reason your water heater may begin producing noise and what you can possibly do to calm it down! Prior to contacting a Moreno Valley expert, check out one of the most frequent water heater difficulties and remedies.

The most possible reason a water heater will make noise

Again, if the sound is an clue of problems with the heater that trouble is probably sediment build up. The sediment stems from the water in the storage tank. It is generally comprised of calcium and magnesium debris and is particularly a difficulty in houses which have hard water.

Whenever the sediment starts to develop at the bottom of the storage tank, it traps a little part of hot water beneath it. This will cause the hot water to boil as the tank works. The sounds noticed are the bubbles popping through the sediment.

Moreover, the sediment itself could be the source of the sounds. The sediment sits at the bottom of the tank and can get burnt up leading to unusual sounds. And on occasion, the sediment can get carried up to the top of the tank and breaks off triggering sounds as it falls back down, striking the sides on its way.


If sediment build-up is what’s creating the sounds, the heater should be reviewed. Water Heater Repair Moreno Valley can accomplish this and provide the tank a flush or recommend an additional option.

You can also reduce the chances of sediment build-up by having expert servicing conducted on the storage tank a minimum of annually. This procedure involves flushing the tank of any sediment.

Yet another good possibility is to set up a water softener in your Moreno Valley house. Water softeners get rid of minerals from the water prior to it entering the water heater, noticeably decreasing sediment build up.

To learn more about other likely concerns and options offer Hot Water Heater Repair Moreno Valley a phone call!

Water Heater Repair Video Overview

We absolutely love the things we do here at Water Heater Repair Moreno Valley CA and look forward to assisting as many of our Moreno Valley neighborhood friends as possible. We will continue to include assistance on water heater maintenance right here in this blog too.

We desire to share our brand new company introduction video to you below.

We are additionally accessible to assist you with every other kind of plumbing repair you may need carried out. Whether it is a leaking faucet, drain cleaning, toilet repair, or leak detection. We have witnessed nearly any sort of emergency plumbing and water heater repair problem you can envision and look forward to utilizing our well crafted troubleshooting ability!

If you are imagining it is becoming near requiring a water heater replacement inform us as well, for we will do all we can to help support you in that scenario.